What Spray Gun Tip Size Do You Need? A Chart for Primer, Basecoat and Clear Coat
Share
Use the fluid tip size printed on the technical data sheet of the coating you are spraying. Across the clears, basecoats, single stages, and primers we stock, the sheets fall into a clear pattern: clear coats call for 1.2 to 1.5 mm, most of them 1.3 to 1.4 mm; basecoat and single stage call for 1.3 to 1.6 mm; primer surfacers and epoxy primers call for 1.3 to 1.8 mm; and high build primers go up to 2.0 to 2.2 mm. The charts below list each product's printed range, so you can set up a gun, or choose one, for the job in front of you.
What tip size do I need for clear coat?
For full-size guns, every clear on this list prints a range between 1.2 and 1.5 mm. Most say 1.3 to 1.4 mm.
| Clear | Fluid tip on the sheet | HVLP air pressure on the sheet |
|---|---|---|
| High Teck 8100 | 1.2–1.4 mm, HVLP/LVLP | 8–10 psi at the air cap |
| High Teck 8550 Speed Clear | 1.3–1.4 mm, gravity | 10 psi at the air cap |
| High Teck 8030 ECO | 1.3–1.5 mm, HVLP gravity or conventional | Not printed |
| High Teck 8720 | 1.3–1.5 mm, gravity or siphon | 8–10 psi at the cap |
| High Teck 77125 | 1.3–1.4 mm, HVLP/LVLP | Not printed |
| Matrix MS-30, MS-42, MS-52 | 1.3–1.4 mm, HVLP/LVLP | Follow the gun maker |
| Kapci 6030 HS | 1.3–1.4 mm, HVLP, compliant or conventional | 8–10 psi atomization; 26–29 psi at the inlet |
| Challenger CH3050 | 1.3–1.4 mm, HVLP gravity or high efficiency | 8–10 psi at the cap |
High Teck 7000 prints no tip size. Its sheet gives "8-10 psi at the gun when using HVLP." For a full comparison of these clears by mix ratio, pot life and polish time, see our guide to choosing an automotive clear coat.
What tip size do I need for basecoat and single stage?
- OMNI MBC basecoat: "1.3 - 1.6 mm or equivalent," 2 to 3 coats or until the color is achieved.
- High Teck HFP basecoat: 1.3 to 1.5 mm for gravity-feed guns, 2 to 4 single coats or until full coverage.
- OMNI MTK single stage: "1.3 - 1.6 mm or equivalent," 2 coats or until the color is achieved.
The MBC and MTK bulletins give HVLP pressure as 8 to 10 psi at the air cap and compliant-gun pressure as 29 to 40 psi at the gun. Mix ratios for both are in our OMNI mixing ratios chart.
What tip size do I need for primer?
Primer ranges are wider. Some primers, such as High Teck 77551, can be mixed thicker for build or reduced as a surfacer. Within the printed range, a heavier mix generally suits a larger tip.
| Primer | Type | Fluid tip on the sheet |
|---|---|---|
| High Teck 7030 ECO-Prime | 2K primer, 4:1 | 1.4–1.7 mm HVLP gravity; 1.5–1.8 mm conventional |
| Matrix MP-2KGR Quick Sand | 2K primer, 4:1 | 1.4–1.7 mm, HVLP/LVLP |
| OMNI MP282 | 2K primer surfacer | 1.3–1.6 mm |
| High Teck 7330 | 2K high solids urethane, 4:1 | 1.3–2.0 mm, HVLP gravity |
| High Teck 77551 Quicksand | 2K urethane primer | 1.5–2.2 mm, conventional and HVLP |
| Matrix MP3-HS Ultra High Build | 2K high build, 4:1 | 1.8–2.0 mm, HVLP/LVLP |
| High Teck 7500 series | Epoxy, 1:1 | 1.5–1.8 mm, conventional gravity or siphon |
| OMNI MP170, MP171, MP172 | Epoxy, 2:1 | 1.3–1.6 mm |
High Teck's 7500 sheet lists its 1.5–1.8 mm tips under conventional guns and gives HVLP only as a pressure: 8 to 10 psi at the cap. For which primer goes where in a paint job, see epoxy primer, 2K primer, or sealer.
What do the tip sizes look like side by side?
3M prints a starting-point chart for its Performance Spray Gun's gravity heads. Its own note says these are "starting points only, refer to Paint Manufacture for recommendation on fluid tip size."
- Clearcoat: 1.2, 1.3 or 1.4 mm
- Solvent basecoat: 1.3 or 1.4 mm
- Single stage topcoat: 1.4 mm
- Primer sealer and wet-on-wet primer: 1.3 or 1.4 mm
- Primer surfacer and high build primer: 1.4, 1.6 or 1.8 mm
- Sprayable fillers and high viscosity coatings: 1.8 or 2.0 mm
Most of the data sheets above sit close to these bands, but several print wider ranges: up to 1.5 mm for clear, 1.6 mm for basecoat and 2.2 mm for high build primer. When the two disagree, the coating's sheet wins.
What air pressure should an HVLP gun run at?
Check where the sheet measures it. Two different numbers get printed:
- At the air cap: most of these sheets give HVLP pressure here, usually 8 to 10 psi. That includes High Teck 8100, 8720 and 7500, Challenger CH3050, Kapci 6030, and the OMNI MBC, MTK, MP282 and MP17x bulletins.
- At the inlet: where the air hose connects. This figure usually comes from the gun maker, though some coating sheets print it too. 3M lists a recommended inlet pressure of 20 psi for the original Performance Spray Gun's gravity heads. Kapci lists 26 to 29 psi at the inlet for HVLP, along with 8 to 10 psi atomizing pressure.
The Matrix clear and primer sheets give no figure and say to follow the spray gun manufacturer's recommendations. Do the same whenever a sheet leaves pressure out.
Do I need one spray gun or two?
It depends on how often you change tips. No clear on this list prints a tip above 1.5 mm, and the high build primers start at 1.5 to 1.8 mm. Three ways to set up:
- A dedicated primer gun. The High Teck T502 and the Titan 19018 are both 1.8 mm HVLP gravity guns with 600 cc cups. 1.8 mm sits inside the printed HVLP range of High Teck 7330 and 77551 and Matrix MP3-HS.
- A dedicated topcoat gun. The SATAjet X 5500 HVLP comes with a 1.3 mm O nozzle, inside the range of every clear and basecoat above.
- One gun with swappable heads. The 3M Performance Spray Gun takes quick-change atomizing heads. 3M says that with these, "paint never passes through the body of the spray gun." The original 26832 takes gravity heads from 1.2 to 2.0 mm.
Before you buy, check your air supply. 3M lists 13 SCFM of air consumption for the Performance Spray Gun. Our T502 listing gives an average of 7 to 9 CFM.
What changed with the 3M Performance Spray Gun 2?
3M unveiled the Performance Spray Gun 2 (26852) in August 2025, according to Repairer Driven News. 3M calls it "our next generation of the 3M Performance Spray Gun." From 3M's data sheet and brochure:
| Performance Spray Gun (26832) | Performance Spray Gun 2 (26852) | |
|---|---|---|
| Gravity head sizes | HVLP 1.2–2.0 mm | HVLP 0.9–2.0 mm, plus Fine Finish heads 0.9–2.0 mm |
| Gravity inlet pressure | 20 psi recommended | HVLP up to 20 psi; Fine Finish 29 psi* |
| Air consumption | 13 SCFM | 13 SCFM |
| Body | Glass-filled nylon | Polyphenylene sulfide; 3M describes the frame as carbon fiber |
| Other changes | — | Laser-marked control knobs, redesigned comfort trigger |
*3M's 2025 data sheet covers both guns in one document. The 20 and 29 psi figures are from that sheet.
Repairer Driven News reports that the Performance Spray Gun 2 works with the original's replacement parts, nozzles, and accessories. 3M's chart marks the new 0.9 and 1.1 mm sizes for jobs such as spot repair and midcoat or effect coats.
Which cup should I use?
3M describes the Performance Spray Gun as convertible to the 3M PPS Series 2.0 cup system. We carry the 650 mL 26000 lids and liners and the 26001 hard cup. 3M says shops using PPS Series 2.0 "often experience a 70% reduction in cleaning solvent usage." Replace the liners and lids rather than clean them.
Spray gun setup checklist
- Find the fluid tip size on the data sheet for the exact product you are spraying.
- Use a bigger tip for heavier primer mixes and a smaller tip for clear, basecoat, and sealer.
- Check whether the sheet's pressure is at the air cap or at the inlet.
- Where the sheet gives no pressure, set the gun to its maker's recommendation.
- Confirm your compressor can supply the gun's CFM.
- Spray a test pattern on paper or a scrap panel before the car.
- Never set the inlet above the gun's maximum pressure.
- 2K clears, primers and activators contain isocyanates. Spray in a ventilated area and wear the respirator, eye and skin protection named on each label and safety data sheet.
Spray guns at AutoColorOnline
Every gun and coating in this guide links to its product page. Browse all automotive paint spray guns, or put a full system together with Build Your Kit.