Compound vs Polish: How to Buff a Fresh Paint Job in 3 Steps, With a Pad Chart

Compound vs Polish: How to Buff a Fresh Paint Job in 3 Steps, With a Pad Chart

Rubbing compound removes sanding scratches. Machine polish removes the swirl marks the compound leaves. An ultrafine polish removes the fine swirls the polish leaves. Each step uses its own pad, and both systems we stock, 3M Perfect-It EX and Wizards Select Pro, pair each liquid with a pad. This guide shows which pad goes with which bottle, what to sand with first, the speeds 3M publishes, and when a step can be skipped.

What is the difference between rubbing compound and polish?

Both are abrasives. They differ in how coarse they are and what they are meant to remove. Mark Clark, writing in BodyShop Business, puts it this way: "Compounds and polishes are basically paste sandpaper."

The manufacturers describe each step by the mark it removes:

  • Compound: 3M calls Perfect-It EX AC its "best-performing rubbing compound for removing P1200 or finer sand scratches." Wizards says Select Pro Extra Cut "Removes P1200 & Finer Sandscratches."
  • Polish: 3M calls Perfect-It EX Machine Polish its "highest-performing machine polish for removing swirl marks after compounding." Wizards says Select Pro Cut & Polish "Removes Compound Swirl Marks."
  • Ultrafine polish: 3M's summary of Perfect-It EX Ultrafine Machine Polish reads, "Quickly and completely removes machine polish swirls, even on black vehicles." Wizards says Select Pro Ultra Fine "Quickly Removes Fine Swirls."

So the order is fixed: each product removes the marks left by the one before it.

Which pad goes with which compound or polish?

Step 3M Perfect-It EX 3M pad Wizards Select Pro Wizards pad
1. Compound 36060 EX AC Rubbing Compound (quart) or 36061 (gallon) Foam compounding pad: 05706 (white, double-sided) or 05737 (single-sided). Or a wool pad. 41001 Extra Cut Wool or white foam cutting pad: 11310 The Aggressor
2. Polish 06094 EX Machine Polish Foam polishing pad: 05707 (gray, double-sided) or 05738 (single-sided) 41002 Cut & Polish Gray foam pad: 11312 The Finisher
3. Ultrafine 06068 EX Ultrafine Machine Polish (quart) or 39062 (pint) Ultrafine foam polishing pad: 05708 (blue, double-sided) or 05733 (single-sided) 41003 Ultra Fine Blue finishing pad: 11314 The Ultra Finishing

Three notes on the chart:

  • 3M's own documents call the polishing pad gray in some places and black in others. Both names are used for part numbers 05707 and 05738.
  • Wizards describes Select Pro as "a Rotary Buffing System" that "is color coordinated with the pad and bottle."
  • The Wizards pad colors are from our listings and from Wizards' Finish Cut directions, which name the white foam cutting pad 11310 and the gray finishing pad 11312.

Should I compound with a wool pad or a foam pad?

3M gives a choice at the compound step. Its Paint Finishing Guide recommends a wool compounding pad "for fastest cut and less heat" and a foam compounding pad to "eliminate lint and achieve the finest finish."

The same guide explains the trade-off: "A wool compounding pad is more aggressive than foam and tends to leave a deeper swirl mark that the technician will need to remove later in the process." 3M says using a foam pad instead of wool reduces swirl comebacks, and adds, "This is very important for dark colored vehicles."

We stock 3M's 100% wool compounding pad as the 05753 (9 inch, Quick Connect) and a 3M double-sided wool compounding pad as the 05703 (9 inch, screw-on).

What should I sand with before buffing?

Compound is rated for P1200 and finer scratches, so the sanding has to finish at least that fine. 3M's finishing process goes further, because finer scratches take less compounding:

  • Remove the defect: a P1500 or P2000 finishing film disc, used dry. 3M recommends P2000 "for the majority of applications" and calls P1500 "still a viable option" for heavy texture and large dirt nibs. We stock P1500 and P2000.
  • Refine the scratches: a Trizact 3000 foam disc, used damp. 3M says to go over each area 5 times. Too much water makes the disc hydroplane; too little loads it.
  • Optional: a Trizact 5000 foam disc, used damp, to cut compounding time further. 3M requires the 3000 step before the 5000.

For the grits used earlier in the job, see our automotive sandpaper grit chart.

What speed and pressure should I buff at?

3M publishes the same speed for all three Perfect-It EX steps: a polisher set between 1,200 and 2,000 RPM. Its data sheets and wall chart add:

  • Area: work a 2 foot by 2 foot area at a time.
  • Compound: start with medium pressure and reduce it as the product begins to dry.
  • Polish: medium pressure to remove swirl marks, then light pressure to polish.
  • Ultrafine: do not buff dry. 3M's sheet says the product "must be used wet to achieve a swirl-free finish."
  • After buffing: remove any film or splatter with a clean detailing cloth.

Wizards does not publish a speed for the Select Pro products. For its Finish Cut compound, Wizards gives 1,400 to 2,200 RPM on a rotary buffer, then 1,000 RPM with the gray finishing pad.

Heat is the thing to watch. Clark's advice in BodyShop Business: "If there's any heat, hold off until the paint cools to the touch."

Do I need all three steps every time?

No. 3M says, "The level of work and stages needed for paint repair depend on the severity of the paint imperfection."

  • Dark colors: plan on the third step. 3M's guide describes the ultrafine step as the way to eliminate fine swirl marks "especially on dark colored cars."
  • Other colors: 3M recommends its machine polish with the foam polishing pad "for the best finish on all colors." The ultrafine step is for fine swirls that still show after that.
  • One bottle: Wizards Finish Cut 11040 is sold for "one step buffing on most colors and clear coat, fresh or aged finishes." Wizards' directions still change pads: a blended wool pad first, then the white foam cutting pad, then the gray finishing pad.

Can I finish without rubbing compound?

3M sells a system for that. Perfect-It 1-Step Finishing Material 33039 is, in 3M's words, "designed to remove 3M Trizact 8000 and finer scratches providing a 1-Step finish on most colours." The sanding does the work that compound would:

  • Remove the defect with P1500 or P2000, then refine with a damp Trizact 3000 disc, as above.
  • Refine again with a damp Trizact 8000 foam disc. 3M does not recommend skipping this step, and it requires the 3000 disc first.
  • Polish with the 1-Step material on the purple 1-Step foam finishing pad 33037, with the polisher between 1,200 and 2,000 RPM and medium pressure.

On black or dark colored paint, 3M says you may still want to follow with an ultrafine polish. 3M also says the 1-Step system was not designed for gelcoat.

What about 3M's tan rubbing compound, gray machine polish, and hand glaze?

These three are separate products from the Perfect-It EX line:

  • 3M 05973 Rubbing Compound: 3M says it "quickly removes sand scratches, oxidation, coarse swirl marks and water spots."
  • 3M 05996 Machine Polish: removes compound swirl marks. 3M says the formula "contains no waxes or silicones."
  • 3M 05990 Hand Glaze: applied by hand with a microfiber cloth after machine polishing. 3M says it is made without wax or silicone.

All three come together in our Compound & Polish bundle.

How soon after painting can I buff?

The 3M and Wizards pages we checked give no wait time. The clear coat's technical data sheet does, and the printed polish or dry times are far apart:

  • High Teck 8550 speed clear: wet sand and buff after 25 minutes at 70°F.
  • High Teck 8100: 24 hours at 70°F.
  • High Teck 77125 and Matrix MS-42: 16 to 24 hours at 77°F.

Those times are printed for 70°F to 77°F. A colder shop takes longer, and the 77125 and MS-42 sheets say not to use those clears below 65°F. Our guide to choosing an automotive clear coat lists the polish or dry time for 13 clears, and painting a car in cold weather covers the temperature limits for each product type.

Which kit matches which system?

Kit What is in it
3M Buff & Polish Full Bundle Quarts of 36060, 06094 and 06068, plus single-sided pads 05737, 05738 and 05733
3M Buff & Polish Bundle Quarts of 36060, 06094 and 06068, no pads
3M Pad Bundle 8 inch pads 05706, 05707 and 05708
Wizards Polish & Pad Kit 41001, 41002 and 41003, plus pads 11310, 11312 and 11314
Wizards Compound, Polish & Machine Finish Kit 41001, 41002 and 41003, no pads

Check how each pad attaches before you order. The double-sided 05707 and 05708 are Quick Connect pads, which mount on a 3M Quick Connect adaptor. The double-sided 05706 works with a Hookit attachment as well as Quick Connect. 3M lists the single-sided 05737, 05738 and 05733 as inset pads for a 3M Hookit backup pad. Our Wizards pad listings give a hook-and-loop attachment.

Buff and polish checklist

  • Wait the polish time on the clear coat's data sheet.
  • Sand defects out with P1500 or P2000, then refine with a damp 3000 disc.
  • Compound with the white foam or wool pad until the sand scratches are gone.
  • Polish with the gray pad to remove the compound swirls.
  • On dark colors, finish with the ultrafine polish and the blue pad. Keep it wet.
  • Use the pad assigned to each product. 3M says to keep a used polishing pad in a plastic bag to prevent contamination.
  • Wipe each panel with a clean microfiber cloth before you inspect it.
  • A rotary polisher can cut through clear coat. Keep the pad moving, go light on edges and body lines, and stop once the scratch is gone.
  • Wear eye protection, and a dust mask when sanding dry. Follow each product's label and safety data sheet.

Buffing and polishing supplies at AutoColorOnline

Browse all compounds, polishes and glazes and buffing and polishing pads.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.